717 Specifications:

• Injection Volume Range: 0.1 uL to 2000 uL in 0.1 uL Increments
• Linearity (1 to 100 uL): > 0.99 Coefficient of deviation
• Carryover: < 0.1 %
• Bandspreading: < 10% Contribution for all solvent systems
• Precision (typical, 5 to 50 uL): <0.5 % RSD
• System Operating Pressure: 4500 psig maximum continuous operating pressure 5000 psig maximum surge for <30 seconds
• Wash Flow, Solvent Rate: > 0.4 mL per injection
• Minimum Sample Required: 7 uL using low volume inserts

• Wetted Surface Materials: 316 Stainless Steel, Teflon, Glass, Fluoraloy-08 R, UHMWPE
• Number of Sample Vials: 1 to 96
• Number of Injections: Programmable 1 to 99 injections per vial
• Allowable Solvents: All standard LC solvents
• Inlet Tubing to Injector: 0.040 I.D. stainless steel
• Outlet Tubing from Injector: 0.009 ID stainless steel
• Total Solvent Volume: 836 uL

• Operating Temperature Range: 4-40 °C
• Relative Humidity: 80%, non-condensing
• Storage Temperature Range: - 40 to 70 °C

• Wavelength range (single, fixed wavelength): 190 to 600 nm
• Wavelength accuracy: ± 2 nm
• Wavelength repeatability: ± 0.25 nm
• Noise: ± 1.0 x 10^-5 AU, 1 second filter setting, 210 to 280 nm) dry cell
• Drift:
  - 1.0 x 10^-4 AU per °C (after warm-up)
  - 1.0 x 10^-4 AU per hour (after warm-up)
• Sensitivity Setting Range: 0.001 to 2.0 AUFS (under software control)
• Filter Setting Range: 0.1 to 5.0 seconds (under software control)
• Bandwidth: 8 nm

• Lamp Source: Deuterium arc lamp
• Flow cell: Dual beam Taper-Cell design
• Path length: 10 mm (standard, analytical)
• Cell volume: 8 ul (standard, analytical)
• Pressure limit: 1000 psi
• Materials: 316 stainless steel, Dynasil Suprasil II, Teflon

• Operating temperature: 15 to 32.2 °C
• Operating humidity: 20 to 80%, non-condensing
• Shipping and storage temperature: -40° to 65 °C
• Shipping and storage humidity: 20 to 80% non-condensing

• Operating temperature: 15.6 to 37.8 °C (40-100 °F)
• Storage temperature: 7.3 to 49.0 °C (20-120 °F)
• Humidity: 0-90%, non-condensing
• Power requirements: 95-135 Vac or 190-270 Vac
• Fuse: 2 A, 120 V or 1 A, 250 V
• Material of wetted surfaces: 316 stainless steel, sapphire, reinforced fluorocarbon polymer
• Flow rate range: 0.1 to 9.9 ml/min; 0.1 ml/min increments
• Flow rate precision: ± 0.3 % at 3 ml/ min (same solvent, constant operating temperature)
• Flow rate accuracy: ± 3% of setting
• Operating pressure limit: 100 to 6000 psi
• Pressure transducer: Flow through Bourdon tube design
• Pressure meter accuracy: ± 10% of reading
• Over pressure limits: ± 15 % of setting
• Piston displacement volume:
  - Primary head: 100 ul
  - Accumulator head: 50 ul
• Power dissipation: 85 watts at 9.9 ml/min and backpressure of 6000 psi